[Bug 2063229] Re: SATA devices on Alder-Lake S not recognized

Same problem here, after upgrading from Ubuntu 23.10 to
24.04(6.8.0-31-generic) it stopped working.

Using kernel 6.8.0-31-generic and 6.8.7-x64v3-xanmod2 the same error
occurs. I'm using 6.6.28-x64v3-xanmod2 to temporarily solve this
problem.

Using: 6.8.0-31-generic

dmesg:
[ 0.788961] kernel: idma64 idma64.0: Found Intel integrated DMA 64-bit
[ 0.789154] kernel: ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf0 impl SATA mode
[ 0.789158] kernel: ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds
[ 0.798278] kernel: nvme nvme0: allocated 32 MiB host memory buffer.
[ 0.799063] kernel: scsi host0: ahci
[ 0.799144] kernel: scsi host1: ahci
[ 0.799187] kernel: scsi host2: ahci
[ 0.799229] kernel: scsi host3: ahci
[ 0.799278] kernel: scsi host4: ahci
[ 0.799326] kernel: scsi host5: ahci
[ 0.799373] kernel: scsi host6: ahci
[ 0.799418] kernel: scsi host7: ahci
[ 0.799439] kernel: ata1: DUMMY
[ 0.799440] kernel: ata2: DUMMY
[ 0.799440] kernel: ata3: DUMMY
[ 0.799441] kernel: ata4: DUMMY
[ 0.799450] kernel: ata5: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522300 irq 131 lpm-pol 0
[ 0.799453] kernel: ata6: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522380 irq 131 lpm-pol 0
[ 0.799454] kernel: ata7: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522400 irq 131 lpm-pol 0
[ 0.799456] kernel: ata8: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522480 irq 131 lpm-pol 0
[ 0.799767] kernel: nvme nvme0: 12/0/0 default/read/poll queues
[ 0.802618] kernel: nvme0n1: p1 p2
[ 0.808595] kernel: intel-lpss 0000:00:15.1: enabling device (0004 -> 0006)
[ 0.809052] kernel: idma64 idma64.1: Found Intel integrated DMA 64-bit
[ 1.020755] kernel: e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[ 1.029682] kernel: usb 1-7: new high-speed USB device number 2 using xhci_hcd
[ 1.085033] kernel: e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) f4:b5:20:47:67:44
[ 1.085045] kernel: e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[ 1.085121] kernel: e1000e 0000:00:1f.6 eth0: MAC: 15, PHY: 12, PBA No: FFFFFF-0FF
[ 1.106605] kernel: ata8: SATA link down (SStatus 4 SControl 300)
[ 1.106840] kernel: ata5: SATA link down (SStatus 4 SControl 300)
[ 1.107020] kernel: ata7: SATA link down (SStatus 4 SControl 300)
[ 1.107059] kernel: ata6: SATA link down (SStatus 4 SControl 300)


lspci | grep -i -e raid -e sata
00:17.0 SATA controller: Intel Corporation Alder Lake-S PCH SATA Controller [AHCI Mode] (rev 11)

lshw
description: SATA controller
product: Alder Lake-S PCH SATA Controller [AHCI Mode]
vendor: Intel Corporation
physical id: 17
bus info: pci@0000:00:17.0
version: 11
width: 32 bits
clock: 66MHz
capabilities: sata ahci_1.0 bus_master cap_list
configuration: driver=ahci latency=0
resources: irq:123 memory:80520000-80521fff memory:80523000-805230ff ioport:3090(size=8) ioport:3080(size=4) ioport:3060(size=32)


lsb_release -rd
Description: Ubuntu 24.04 LTS
Release: 24.04

apt-cache policy linux-image-6.8.0-31-generic
linux-image-6.8.0-31-generic:
Installed: 6.8.0-31.31

-----------

Using kernel 6.6.28-x64v3-xanmod2 which is working:

dmesg
[ 0.706843] kernel: idma64 idma64.0: Found Intel integrated DMA 64-bit
[ 0.708855] kernel: ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf0 impl SATA mode
[ 0.708859] kernel: ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds
[ 0.713211] kernel: nvme nvme0: allocated 32 MiB host memory buffer.
[ 0.714590] kernel: nvme nvme0: 12/0/0 default/read/poll queues
[ 0.717412] kernel: nvme0n1: p1 p2
[ 0.726589] kernel: intel-lpss 0000:00:15.1: enabling device (0004 -> 0006)
[ 0.726830] kernel: idma64 idma64.1: Found Intel integrated DMA 64-bit
[ 0.751112] kernel: scsi host0: ahci
[ 0.751461] kernel: scsi host1: ahci
[ 0.751697] kernel: scsi host2: ahci
[ 0.751886] kernel: scsi host3: ahci
[ 0.751942] kernel: scsi host4: ahci
[ 0.752023] kernel: scsi host5: ahci
[ 0.752070] kernel: scsi host6: ahci
[ 0.752118] kernel: scsi host7: ahci
[ 0.752140] kernel: ata1: DUMMY
[ 0.752141] kernel: ata2: DUMMY
[ 0.752141] kernel: ata3: DUMMY
[ 0.752142] kernel: ata4: DUMMY
[ 0.752147] kernel: ata5: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522300 irq 125
[ 0.752149] kernel: ata6: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522380 irq 125
[ 0.752151] kernel: ata7: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522400 irq 125
[ 0.752153] kernel: ata8: SATA max UDMA/133 abar m2048@0x80522000 port 0x80522480 irq 125
[ 0.950924] kernel: e1000e 0000:00:1f.6 0000:00:1f.6 (uninitialized): registered PHC clock
[ 0.958644] kernel: usb 1-7: new high-speed USB device number 2 using xhci_hcd
[ 1.018806] kernel: e1000e 0000:00:1f.6 eth0: (PCI Express:2.5GT/s:Width x1) f4:b5:20:47:67:44
[ 1.018809] kernel: e1000e 0000:00:1f.6 eth0: Intel(R) PRO/1000 Network Connection
[ 1.018885] kernel: e1000e 0000:00:1f.6 eth0: MAC: 15, PHY: 12, PBA No: FFFFFF-0FF
[ 1.065350] kernel: ata7: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.066348] kernel: ata7.00: ATA-8: ST1000DM010-2EP102, CC43, max UDMA/133
[ 1.066385] kernel: ata8: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.066429] kernel: ata5: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.066520] kernel: ata7.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.066729] kernel: ata6: SATA link down (SStatus 0 SControl 300)
[ 1.066935] kernel: ata8.00: ATA-10: WDC WD20EFAX-68FB5N0, 82.00A82, max UDMA/133
[ 1.067236] kernel: ata5.00: ATA-10: CT120BX300SSD1, M2CR021, max UDMA/133
[ 1.067390] kernel: ata5.00: 234441648 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.067796] kernel: ata7.00: configured for UDMA/133
[ 1.067999] kernel: ata5.00: Features: Dev-Sleep
[ 1.068650] kernel: ata5.00: configured for UDMA/133
[ 1.068793] kernel: scsi 4:0:0:0: Direct-Access ATA CT120BX300SSD1 021 PQ: 0 ANSI: 5
[ 1.069013] kernel: sd 4:0:0:0: Attached scsi generic sg0 type 0
[ 1.069028] kernel: sd 4:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[ 1.069036] kernel: sd 4:0:0:0: [sda] Write Protect is off
[ 1.069038] kernel: sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.069053] kernel: sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.069064] kernel: sd 4:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[ 1.069226] kernel: scsi 6:0:0:0: Direct-Access ATA ST1000DM010-2EP1 CC43 PQ: 0 ANSI: 5
[ 1.069381] kernel: sd 6:0:0:0: Attached scsi generic sg1 type 0
[ 1.069391] kernel: sd 6:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB)
[ 1.069392] kernel: sd 6:0:0:0: [sdb] 4096-byte physical blocks
[ 1.069399] kernel: sd 6:0:0:0: [sdb] Write Protect is off
[ 1.069401] kernel: sd 6:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.069412] kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.069418] kernel: sd 6:0:0:0: [sdb] Preferred minimum I/O size 4096 bytes
[ 1.069816] kernel: sda: sda1 sda2
[ 1.069867] kernel: sd 4:0:0:0: [sda] Attached SCSI disk
[ 1.077921] kernel: ata8.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 32), AA
[ 1.077933] kernel: ata8.00: Features: NCQ-prio
[ 1.078158] kernel: sdb: sdb1
[ 1.078202] kernel: sd 6:0:0:0: [sdb] Attached SCSI disk
[ 1.089578] kernel: ata8.00: configured for UDMA/133
[ 1.089771] kernel: scsi 7:0:0:0: Direct-Access ATA WDC WD20EFAX-68F 0A82 PQ: 0 ANSI: 5
[ 1.089915] kernel: sd 7:0:0:0: Attached scsi generic sg2 type 0
[ 1.089948] kernel: sd 7:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 1.089950] kernel: sd 7:0:0:0: [sdc] 4096-byte physical blocks
[ 1.089954] kernel: sd 7:0:0:0: [sdc] Write Protect is off
[ 1.089956] kernel: sd 7:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.089962] kernel: sd 7:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.089968] kernel: sd 7:0:0:0: [sdc] Preferred minimum I/O size 4096 bytes
[ 1.098731] kernel: sdc: sdc1
[ 1.098855] kernel: sd 7:0:0:0: [sdc] Attached SCSI disk

lshw
description: SATA controller
product: Alder Lake-S PCH SATA Controller [AHCI Mode]
vendor: Intel Corporation
physical id: 17
bus info: pci@0000:00:17.0
version: 11
width: 32 bits
clock: 66MHz
capabilities: sata ahci_1.0 bus_master cap_list
configuration: driver=ahci latency=0
resources: irq:125 memory:80520000-80521fff memory:80523000-805230ff ioport:3090(size=8) ioport:3080(size=4) ioport:3060(size=32) memory:80522000-805227ff

--
You received this bug notification because you are subscribed to linux
in Ubuntu.
Matching subscriptions: Bgg, Bmail, Nb
https://bugs.launchpad.net/bugs/2063229

Title:
SATA devices on Alder-Lake S not recognized

Status in linux package in Ubuntu:
Confirmed

Bug description:
Ubuntu Jammy (kernel 5.15.0-94) and Ubuntu Noble (kernel 6.8.0-22)
installations and Ubuntu Mantic installed hard drive (kernel
6.5.0-28-generic) are unable to find SATA devices on Alder-Lake S
Intel SATA controller.

Ubuntu Focal and Bionic works just fine. Debian 12 (kernel 6.1.0-18)
and other debian based distros (Mint, Kali, OpenMediaVault, Proxmox)
works just fine.

relevant dmesg logs:
2024-04-19T17:18:50.668222+00:00 ubuntu-server kernel: ahci 0000:00:17.0: version 3.0
2024-04-19T17:18:50.668356+00:00 ubuntu-server kernel: ahci 0000:00:17.0: AHCI 0001.0301 32 slots 4 ports 6 Gbps 0xf0 impl SATA mode
2024-04-19T17:18:50.668358+00:00 ubuntu-server kernel: ahci 0000:00:17.0: flags: 64bit ncq sntf led clo only pio slum part ems deso sadm sds
2024-04-19T17:18:50.668361+00:00 ubuntu-server kernel: intel-lpss 0000:00:15.0: enabling device (0004 -> 0006)
2024-04-19T17:18:50.668362+00:00 ubuntu-server kernel: idma64 idma64.0: Found Intel integrated DMA 64-bit
2024-04-19T17:18:50.668363+00:00 ubuntu-server kernel: scsi host0: ahci
2024-04-19T17:18:50.668364+00:00 ubuntu-server kernel: scsi host1: ahci
2024-04-19T17:18:50.668370+00:00 ubuntu-server kernel: scsi host2: ahci
2024-04-19T17:18:50.668371+00:00 ubuntu-server kernel: scsi host3: ahci
2024-04-19T17:18:50.668372+00:00 ubuntu-server kernel: scsi host4: ahci
2024-04-19T17:18:50.668373+00:00 ubuntu-server kernel: scsi host5: ahci
2024-04-19T17:18:50.668374+00:00 ubuntu-server kernel: scsi host6: ahci
2024-04-19T17:18:50.668380+00:00 ubuntu-server kernel: scsi host7: ahci
2024-04-19T17:18:50.668383+00:00 ubuntu-server kernel: ata1: DUMMY
2024-04-19T17:18:50.668385+00:00 ubuntu-server kernel: ata2: DUMMY
2024-04-19T17:18:50.668386+00:00 ubuntu-server kernel: ata3: DUMMY
2024-04-19T17:18:50.668387+00:00 ubuntu-server kernel: ata4: DUMMY
2024-04-19T17:18:50.668388+00:00 ubuntu-server kernel: ata5: SATA max UDMA/133 abar m2048@0x82222000 port 0x82222300 irq 123 lpm-pol 3
2024-04-19T17:18:50.668389+00:00 ubuntu-server kernel: ata6: SATA max UDMA/133 abar m2048@0x82222000 port 0x82222380 irq 123 lpm-pol 3
2024-04-19T17:18:50.668390+00:00 ubuntu-server kernel: ata7: SATA max UDMA/133 abar m2048@0x82222000 port 0x82222400 irq 123 lpm-pol 3
2024-04-19T17:18:50.668391+00:00 ubuntu-server kernel: ata8: SATA max UDMA/133 abar m2048@0x82222000 port 0x82222480 irq 123 lpm-pol 3
2024-04-19T17:18:50.668392+00:00 ubuntu-server kernel: ahci 0000:02:00.0: enabling device (0000 -> 0003)
2024-04-19T17:18:50.668393+00:00 ubuntu-server kernel: ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
2024-04-19T17:18:50.668394+00:00 ubuntu-server kernel: ahci 0000:02:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
2024-04-19T17:18:50.668395+00:00 ubuntu-server kernel: ahci 0000:02:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs
2024-04-19T17:18:50.668396+00:00 ubuntu-server kernel: scsi host8: ahci
2024-04-19T17:18:50.668397+00:00 ubuntu-server kernel: scsi host9: ahci
2024-04-19T17:18:50.668398+00:00 ubuntu-server kernel: ata9: SATA max UDMA/133 abar m512@0x82110000 port 0x82110100 irq 130 lpm-pol 0
2024-04-19T17:18:50.668399+00:00 ubuntu-server kernel: ata10: SATA max UDMA/133 abar m512@0x82110000 port 0x82110180 irq 130 lpm-pol 0
2024-04-19T17:18:50.668400+00:00 ubuntu-server kernel: intel-lpss 0000:00:15.1: enabling device (0004 -> 0006)
2024-04-19T17:18:50.668401+00:00 ubuntu-server kernel: idma64 idma64.1: Found Intel integrated DMA 64-bit
2024-04-19T17:18:50.668407+00:00 ubuntu-server kernel: ata7: SATA link down (SStatus 4 SControl 300)
2024-04-19T17:18:50.668408+00:00 ubuntu-server kernel: ata9: SATA link down (SStatus 0 SControl 300)
2024-04-19T17:18:50.668409+00:00 ubuntu-server kernel: ata5: SATA link down (SStatus 4 SControl 300)
2024-04-19T17:18:50.668410+00:00 ubuntu-server kernel: ata6: SATA link down (SStatus 4 SControl 300)
2024-04-19T17:18:50.668411+00:00 ubuntu-server kernel: ata8: SATA link down (SStatus 4 SControl 300)
2024-04-19T17:18:50.668435+00:00 ubuntu-server kernel: ata10: SATA link down (SStatus 0 SControl 300)
2024-04-19T17:18:50.668466+00:00 ubuntu-server kernel: raid6: avx2x4 gen() 37283 MB/s
2024-04-19T17:18:50.668467+00:00 ubuntu-server kernel: raid6: avx2x2 gen() 39645 MB/s
2024-04-19T17:18:50.668468+00:00 ubuntu-server kernel: raid6: avx2x1 gen() 35756 MB/s
2024-04-19T17:18:50.668469+00:00 ubuntu-server kernel: raid6: using algorithm avx2x2 gen() 39645 MB/s
2024-04-19T17:18:50.668470+00:00 ubuntu-server kernel: raid6: .... xor() 25680 MB/s, rmw enabled
2024-04-19T17:18:50.668477+00:00 ubuntu-server kernel: raid6: using avx2x2 recovery algorithm
2024-04-19T17:18:50.668478+00:00 ubuntu-server kernel: xor: automatically using best checksumming function avx
2024-04-19T17:18:50.668479+00:00 ubuntu-server kernel: async_tx: api initialized (async)

lspci | grep -i -e raid -e sata
00:17.0 SATA controller: Intel Corporation Device 7ae2 (rev 11)

lshw
description: SATA controller
product: Alder Lake-S PCH SATA Controller [AHCI Mode]
vendor: Intel Corporation
physical id: 17
bus info: pci@0000:00:17.0
version: 11
width: 32 bits
clock: 66MHz
capabilities: sata ahci_1.0 bus_master cap_list
configuration: driver=ahci latency=0
resources: irq:125 memory:80520000-80521fff memory:80523000-805230ff ioport:3090(size=8) ioport:3080(size=4) ioport:3060(size=32) memory:80522000-805227ff

lsb_release -rd (from Mantic installed)
Description: Ubuntu 23.10

apt-cache policy linux-image-6.5.0-28-generic (from Mantic installed)
Installed: 6.5.0-28.29

To manage notifications about this bug go to:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/2063229/+subscriptions